- Refine By >
Regarding to one of the most fast servos in the micro class, DES 291 BB MG digital micro motor that features Graupner's exclusive programmable digital circuit and Heavy duty Metal gear offers long life and all the performance you would expect to find in a more expensive servo. Digital servo featuring dynamic torque, excellent Speed, superior response and holding torque. Programmable Digital Circuit and SMT circuitry. Supporting 116µ depending on programming. Covering the wide range of frame rate 20Hz400Hz.
This is a heavy duty 300mm servo extension for use with JR Airtronics and Hitec RCD radio systems- High quality components- Constructed from the finest materials- SKU: RCHOB0064 SKU: RCHOB0064
Specifications Dimensions: 40mm x 20mm x 38.1mm Speed: 0.2 sec / 60 angle at 6v Torque: 8.9 kg-cm at 6v Bearing: 2BB Features - Metal Gear - Double Ball Bearing - Connector Wire Length 300mm This is special edition bundle with RCECHO Apps license key included for more fun!. RCECHO is a registered trademarks. Products only distributed by authorized seller.
This is a Heavy Duty 36" Servo Extension with Hitec-S, JR, Airtronics-Z Connectors.This extension goes between the receiver and the servo to make the wire longer. On one end of the wire is a male connector and on the other end of the wire is a female connector.FEATURES: Gold-plated teminals improve conductivity and prevent oxidation for longer lifespan. Heavier, 20-gauge wire handles higher current loads.INCLUDES: One 36" Long Servo Extension w/Hitec-S, JR, Airtronics-Z Style ConnectorsSPECS: Wire Gauge: 20
This is a Hitec Programmable Standard Digital Servo with Hitec "S" Type Connector. FEATURES: Four heavy duty Karbonite gears Top ball bearing Programmable Digital Designed for .20-.60 Airplanes, Steering & Throttle Servo, and Trucks and Boats YOU WILL RECEIVE: One servo with pre-installed round (disk) servo horn Four grommets Four brass eyelets Four round, flanged, phillips head screws 1.5 x 14mm One adjustable servo horn One large X servo horn 1.7" (43mm) end to end One small X servo horn 1.2" (30mm) end
"This is the Futaba S9255 Digital High-Torque Servo / for helicopter usage. / / FEATURES: Comes with heavy duty wiring that can handle higher current loads / Ball bearing output shaft / Metal gears / Coreless motor, a conventional servo motor has a steel core armature / wrapped with wire that spins inside magnets. In Coreless designs, / the armature uses a thin wire mesh that forms a cup that spins / around the outside of the magnet eliminating the heavy steel core. / This design is much lighter resulting
HS-322HD Standard Heavy Duty Servo The HS-322HD Standard Heavy Duty Servo utilizes Hitec's revolutionary Karbonite™ gear train which is four times stronger than the standard white nylon gears. Even after hundreds of thousands of cycles, t
100 Feet of Spektrum / JR colored heavy duty servo wire. 22 gauge wire, 60 strand wire count. Make your own extensions!Shipping is $7.00 in the US. No International Shipping.
FlyingNation eBay Ads - MIRACLE RC V2 HEAVY DUTY 3.5" FULL LONG SERVO ARM/TILLER FOR FUTABA http://www.rcflightdepot.com/item/P/LSM-MC-F022F_D_2.jpg" width="92" alt="MIRACLE RC V2 HEAVY DUTY 3.5" FULL LONG SERVO ARM/TILLER FOR HITEC" style = "margin -bottom : 3px;" onclick = "document .swap .src = 'http : / /www .rcflightdepot .com /item /P /LSM -MC -F022F _D _2 .jpg ' " ';" http://www.rcflightdepot.com/item/P/LSM-MC-F022F_D_3.jpg" width="92" alt="MIRACLE RC V2 HEAVY DUTY 3.5" FULL LONG SERVO ARM/TILLER FOR
Rated for 2S LiPo operation Heavy duty metal gears and dual ball bearings Coreless motor Two year limited warranty through Hitec beginning at date of purchase </ul>
FlyingNation eBay Ads - MIRACLE RC V3 HEAVY DUTY 1.75"/2" HALF LONG SERVO ARM FOR HITEC http://www.rcflightdepot.com/item/P/LSM-MC-F025H_D_2.jpg" width="92" alt="MIRACLE RC V3 HEAVY DUTY 1.75"/2" HALF LONG SERVO ARM FOR HITEC" style = "margin -bottom : 3px;" onclick = "document .swap .src = 'http : / /www .rcflightdepot .com /item /P /LSM -MC -F025H _D _2 .jpg ' " ';" http://www.rcflightdepot.com/item/P/LSM-MC-F025H_D_3.jpg" width="92" alt="MIRACLE RC V3 HEAVY DUTY 1.75"/2" HALF LONG SERVO ARM FOR HITEC"
The HS-7954SH could be considered the most economical high voltage, high torque, coreless servo on the market. Based on the ultra popular HS-7955TG, the HS-7954SH has the added benefit of our high voltage coreless motor. With 403 inch ounce of torque at 7.4 volts, the HS-7954SH is fast too with a 0.12 second transit time when operating on a 2 cell LiPo pack. The HS-7954SH harnesses all this power by utilizing a heavy duty case that incorporates an aluminum heat sink, hardened steel gears, and two strong
The new HS -7985MG High Torque Digital Servo has the added benefit of our new G2 second generation programmable digital circuit. This circuit has twice the resolution of our original circuit while adding programmable overload protection. The technology doesnt stop at the circuit board, with a high performance coreless motor, dual ball bearing supported output shaft, bushing supported gear shafts and our Heavy Duty Metal gear train the HS -7985MG was designed to withstand the stress of larger high
Hitec 50' 3-color heavy gauge servo wire comes in a 50 foot roll, great for the do-it-yourselfer. Colored black (outside), red (middle), and yellow (outside). Make custom length wires for servos or receiver batteries leads. Heavy duty 20 gauge.
The DES 567 MG thin Digital Servo is an ideal combination of torque, speed and holding power. Combined with Heavy duty metal gear and SMT circuitry, the low deadband technology and SJ's exclusive programmable digital circuit help that you enjoy reliable accuracy and precision. DES 567 MG represents a remarkable value in today's R/C market. Digital servo featuring dynamic torque, excellent speed, superior response and holding torque. Programmable Digital Circuit and SMT circuitry. Supporting 116µs response
FlyingNation eBay Ads - MIRACLE RC V2 HEAVY DUTY 2.5" FULL LONG SERVO ARM/TILLER FOR HITEC http://www.rcflightdepot.com/item/P/LSM-MC-F021H_D_2.jpg" width="92" alt="MIRACLE RC V2 HEAVY DUTY 2.5" FULL LONG SERVO ARM/TILLER FOR HITEC" style = "margin -bottom : 3px;" onclick = "document .swap .src = 'http : / /www .rcflightdepot .com /item /P /LSM -MC -F021H _D _2 .jpg ' " ';" http://www.rcflightdepot.com/item/P/LSM-MC-F021H_D_3.jpg" width="92" alt="MIRACLE RC V2 HEAVY DUTY 2.5" FULL LONG SERVO ARM/TILLER FOR
HPI SFL-11MG SERVO(METAL GEAR/FeaturesThis is a HPI SFL-11MG Metal Gear Analog ServoFeatures precise neutral position, heavy duty connector, smooth operation and water resistantIncludes HPI SFL-11MG Servo with Heavy Duty Horn and Instructions
:: Futaba AEC20 Heavy Duty Servo Extension w/Filter 220mm AEC20 Futaba AEC20 Heavy Duty Servo Extension w/Filter 220mm AEC20 Details FUTM4180 AEC20 Futaba AEC20 Heavy Duty Servo Extension w/Filter 220mm AEC20 This is the Futaba 220mm Heavy Duty Extension with Filter . Features Futaba AEC20 Heavy Duty Servo Extension w/Filter 220mm AEC20 Installs between receiver and servo to lengthen servo lead Protects against possible noise in the line associated with long aileron servo leads Specifications Length
Cirrus CIRCJ0300HD Heavy Duty 300Mm Servo Extension - Jr/Airtronics/Rcd
Hitec HS-7954SH harnesses all this power is by utilizing a heavy duty case that incorporates an aluminum heat sink, hardened steel gears, two strong steel gear pins nested in brass axial bushings. Put it all together and you get one tough high voltage servo at a price that can't be beat. Features : Ideal for giant scale planes, large helicopters, rock crawlers, monster trucks, 1/8 scale trucks and buggies and anywhere a high performance, high torque servo is needed Coreless motor for precise centering and
The HBS 870 BB MG is designed to operate on a two cell LiPo Pack. Featuring heavy duty metal gear and offers Super Torque, the high resolution programmable digital circuit and the low deadband technology helps that you enjoy reliable accuracy and precision. The heat sink case will provide lower operating temperatures, longer run times. At least FIVE TIMES longer-lasting, 30% faster response times than brushed servos. Programmable Digital Circuit and SMT circuitry. Supporting 116µs response depending on
Lynx LX0921 - PROTOS 500 - Heavy Duty Tail Servo Mount - Red Devil LX0921 Product description The Protos 500 is an amazing helicopter. Lynx has looked closely at the helicopter’s performance, and we have found a number of areas for improvement. One issue we noted was the standard heli Tail Servo Mount. These parts originally in plastic can’t clamp the boom as need, than vibe or tail wag can upend, reducing tail performance. Lynx Heli Innovations has redesigned the standard Protos 500 plastic tail servo
The A7040's wide stance and low profile design along with its heavy duty metal gears, cored motor and class leading, 266 oz.-in. of torque, is ideal for mechanical retract systems. Its ability to accept a higher voltage from a 2S Li-Po battery makes setup simpler and operation more efficient. Fully proportional with endpoint adjustable, when paired with a servo speed function, the landing gear movement can be adjusted to simulate scale applications.
This is the Futaba S9156 Digital Heavy Duty High Torque Servo. FEATURES: Ideal for any heavy duty loads such as control surfaces on 1/3 scale and larger airplanes and jets as well as boat rudders Metal gear train eliminates backlash and slop Aluminum center case helps to dissipate heat One year warranty INCLUDES: Futaba S9156 Digital Heavy Duty High Torque Servo with Universal connector REQUIRES: Installing in model and connecting to receiver SPECS: Torque: 272 oz/in (19.6 kg/cm) @ 4.8V 340 oz/in (24.5
Miracle RC Heavy Duty 3.5" Full Servo Arm For Hitec - Purple Miracle RC Heavy Duty 3.5" Full Servo Arm For Hitec - Purple Part Num: LSA -MC -F008H -PP Miracle RC Heavy Duty 3.5" Full Servo Arm For Hitec Servos. Nice CNC aluminum in purple anodized color. Super strong and light weight.
Heavy duty Servo Has very high torque. The default 90 degree HS-5645MG can be reconfigured to provide 180 degrees by digital Servo programmers such as HFP-25 Great Servo lots of torque Review by thomas Very High Torque for a nice small sized Servo Motor works great (Posted on 7/7/14) great product Review by thomas lots of torque (Posted on 6/16/14) great servo motor Review by thomas lots of torque (Posted on 6/16/14) very good servo Review by Fotis much better than the same model with the plastic gears
This is the Spektrum S6030 Digital Surface High Torque Servo. Features: Heavy-duty Overload protection Mounting lug height optimized for surface applications Delivers torque with silky smooth precision Dual ball-bearing output shaft 8 inch 22AWG lead The S6030 is a metal gear, heavy-duty servo that puts out an incredible 278 oz-in of torque, making it the ideal 1/10 scale servo for buggies, monster trucks, and truggies. And the S6030 servo delivers this torque with silky smooth precision thanks to its dual
S3801 Futaba S3801 Servo Heavy Duty Arm Type Sail Control [ S3801 ] USD $56 .00 This is a High Torque, Arm-Type Sail Servo with a Metal Output Gear for boat applications requiring approximately 200 oz-in torque. Futaba products have One-Year Warranty. This servo can produce high-current draw from your batteries if using NiMH or LiPo batteries, make sure they are capable of delivering sufficient amps. Metal output gear and the other gears are nylon Two Ball Bearings 3-pole motor Sail Arm included