- Refine By >
"This is the Replacement Gearbox Set for the Traxxas E-Maxx Truck. The gearbox contains all of the gears and is mounted below the two motors.FEATURES: Black plastic constructionINCLUDES : Two Gearbox halves (Front and Rear) One 40mm Guide Pin Five 3x12mm Roundhead Self-Tapping Screws Two Idler Gear Shafts One Idler Gear Shaft SupportREQUIRES: Remainder of the gearbox contents.SPECS: Length: 87mm (3.425"") (At widest point) Width: 60mm (2.37"") (At widest point) Outside Depth: 24.3mm (.957"") Idler Gear
This is the replacement 20 Tooth Idler Gear and Shaft for the Traxxas E-Maxx 4WD RTR. FEATURES: Steel construction, gun metal in color Replaces a worn or damaged idler gear and shaft YOU WILL RECEIVE: One 20 Tooth Idler Gear One 5x18mm Idler Gear Shaft REQUIREMENTS: Installation following the model manual SPECIFICATIONS: Outside Diameter: .86" (22mm) Inside Diameter: .43" (11mm) Thickness: .50" (12.5mm) kpm01/22/2008 ir/jxs &
Traxxas Complete Center Differential For E-Revo and E-Maxx. #5614 Notes: Assembled with 500K oil For use with single speed transmission only.
This is the replacement 13 Tooth Idler Gear (first speed gear) for the Traxxas two-speed conversion for the E-Maxx - TRAC4000. FEATURES: Steel construction, gun metal in color Replaces a worn or damaged idler gear YOU WILL RECEIVE: One 13 Tooth Idler Gear (first speed gear) REQUIREMENTS: Installation kpm03/06/2008 ir/jxs &FeaturesSteel construction, gun metal in color.Replaces a worn or damaged idler gear.Made with the Best Quality Material with your child in mind.Top Quality Children's Item.
GHH02191 02191 Alum Gear Box Blue T-Maxx 2.5/3.3/E-Maxx
"This is the Input Shaft/Drive Gear Assembly for the Traxxas E-Maxx Truck. This assembly is located in the gearbox. FEATURES: Steel construction 18T and 13T gears Pre-assembled on shaft YOU WILL RECEIVE: One Input Shaft/Drive Gear Assembly REQUIREMENTS: Installation into gearbox SPECIFICATIONS: Length: 72.4mm (2.85"") Shaft diameter: 5mm (0.198"") cmc 1/21/01 ir/jl &"
Traxxas replacement input shaft/drive gear assembly for the Traxxas 3905 E-Maxx Truck. Steel shaft, black in color. Steel drive gear assembly, silver in color. Requires: Installation following the model manual
Driveshaft, steel constant-velocity (shaft only, 112mm)/ drive cup pin (1) (fits rear center shaft on 3905 E-Maxx)
This is a Constant Velocity Shaft for the Traxxas E-Maxx- Steel construction- Can be used to replace a bent or damaged constant velocity shaft- Includes: One steel constant-velocity driveshaft- Requires: Installing in vehicle following instructions in manual- Length: 2-17'' (55mm)- Diameter: 19'' (5mm)- SKU: RCHOB1076 SKU: RCHOB1076
This gear cover includes a telemetry sensor port (sensor and wire retainer sold separately). The gear cover is required to enable RPM and speed telemetry data. Fits E-Maxx (3903).
These are the Slipper Friction Pegs (12) for several Traxxas vehicles that have a slipper clutch- Part Compatibility:- Traxxas E-Maxx- Traxxas Nitro Rustler- Traxxas Nitro Stampede SKU: RCHOB0939 SKU: RCHOB0939
Traxxas replacement gearbox halves for the Traxxas E-Maxx Truck- Constructed of black plastic- Requires: Remainder of the gearbox contents- Length: 2-67'' (68mm) (at widest point)- Width: 3-42'' (87mm) (at widest point)- SKU: RCHOB0836 SKU: RCHOB0836
This is the Traxxas Driveshaft Assembly for the Revo 3.3, T-Maxx 2.5R, T-Maxx 3.3, and E-Maxx 3905 vehicles. This is the driveshaft that goes from the differential to the wheel. This will work on the front or rear, right or left of the truck. Features: Fully assembled Plastic telescoping driveshaft with steel universals Blue rubber boot shields telescoping sections from dirt Attaches to the differential with one screw pin Works on the front or rear, right or left of vehicle Includes: #5458X Yoke #5145 Screw
These are the replacement slipper and differential rings for the Traxxas kits that have slipper clutches and ball diffs- They are metal rings with a notch in them and are installed on either side the differential gear or the spur gear- Part Compatibility:- Traxxas E-Maxx- Traxxas Nitro Rustler- Traxxas Nitro Stampede- SKU: RCHOB0931 SKU: RCHOB0931
This is the Golden Horizons Blue Aluminum Gear Box Collar for the Traxxas E-Maxx. Features: Blue colored Made of aluminum For the Traxxas E-Maxx Includes: One Golden Horizons Blue Aluminum Gear Box Collar
This is the replacement Input Shaft/Drive Gear Assembly for the Traxxas 3905 E-Maxx Truck- Steel shaft Black in color Steel drive gear assembly silver in color- Includes: One Input Shaft with 18 Tooth Top Gear- Requires: Installation following the model manual- Shaft Diameter: 5mm- Shaft Length: 3-53'' (90mm)- Thread Size: 4mm- SKU: RCHOB0837 SKU: RCHOB0837
Traxxas Center Driveshafts Steel Constant-Velocity - E-Maxx Traxxas Traxxas Center Driveshafts Steel Constant-Velocity - E-Maxx - Part Number - TRA5151R Traxxas Center Driveshafts Steel Constant-Velocity - E-Maxx 40.00 Our Price: $32.47 TRA5151R
Traxxas RC Parts Idler Gear 20T\Idler Gear Shaft E-Maxx Traxxas RC Parts Idler Gear 20T\Idler Gear Shaft E -Maxx $5 .50 TRA3996X Rating : Shipping : Product Description This is the replacement 20 Tooth Idler Gear and Shaft for the Traxxas E-Maxx 4WD RTR. FEATURES: Steel construction gun metal in color. Replaces a worn or damaged idler gear and shaft. INCLUDES: One 20 Tooth Idler Gear One 5x18mm Idler Gear Shaft. REQUIRES: Installation following the model manual SPECS: Outside Diameter: .86 (22mm)
Traxxas output gear set for the E-Maxx- Constructed of white plastic- Requires: Installation into transmission- Satisfaction ensured- SKU: RCHOB0833 SKU: RCHOB0833
Traxxas Shift Fork Shift Assembly E-Maxx This is the Shift Fork-Shaft Assembly with Seal for the Traxxas E-Maxx Off-Road Truck. This Shift Fork fits into the transmission and over the Drive Dog Carrier
This is the Shift Fork and Shaft included with the optional Two Speed Conversion Kit, TRAC4000 used on the Traxxas E-Maxx. FEATURES: Helps to control shifting of gears when the two speed conversion kit is installed YOU WILL RECEIVE: Shift Fork and Shaft REQUIREMENTS: Installing over the Carrier/Drive Dog (TRAC3986) in the gearbox jxs 3/04/08 ir/jxs &
Traxxas transmission output shaft for the E-Maxx- Constructed of black metal- Installation on the Traxxas E-Maxx- Overall length: 2-75'' (70mm)- Diameter of drive dog mount: -39'' (10mm)- Diameter of shaft: -23'' (6mm)- SKU: RCHOB0819 SKU: RCHOB0819